Actualités de l'industrie

SPD Factory Audit Checklist: 9 Checks Before You Buy

How do you audit an SPD factory before you buy? Use this 9-check audit checklist covering type-test reports, MOV sourcing, QC records and lab capability.

Wind Turbine surge protection: How to choose the right SPD for wind power systems

This guide explains how to choose the right SPD for wind turbine and wind power systems. It covers Type 1, Type 2, and Type 1+2 surge protectors, key 690V parameters such as Uc, In, Imax, Up, and the best installation locations for wind farm electrical protection.

Electrical SPD for Solar PV Systems: Do You Really Need It?

Solar PV systems face real surge risks from lightning and switching events. This guide explains why a dedicated electrical SPD - your solar surge protection device - is essential, and how to select the right PV surge protection device for residential, commercial, and industrial arrays.

SPD Surge Protective Device Protection For Critical Electrical Loads

This B2B guide explains how SPD surge protective devices shield critical electrical loads across data centers, industrial plants, healthcare, and renewable energy systems. It compares Type 1, Type 2, and Type 3 SPDs and provides a practical checklist for choosing reliable surge protective device suppliers.

How Long Do Industrial Surge Protectors Last? Lifespan And Replacement Guide

This guide explains the real-world lifespan of industrial surge protective devices (SPDs), the factors that accelerate aging, the warning signs of end-of-life, testing and maintenance best practices, replacement timing, and total cost considerations. It also shows how to choose a reliable SPD company and compares industrial SPDs with standard consumer surge protectors. Written for plant engineers, facilities managers, and electrical contractors sourcing B2B surge protection solutions.

Single Phase Surge Protection: 1P vs 1P+N vs 2P Compared

Single phase surge protection is supplied in three pole configurations, and choosing between them decides whether the neutral conductor is protected at all. This comparison examines 1P, 1P+N and 2P devices side by side. A 1P device protects the line conductor to earth only, making it the simplest and narrowest option. A 1P+N device adds neutral to earth protection through a dedicated spark gap stage alongside line to neutral protection. A 2P device provides full protection across both line and neutral conductors. The article compares all three by the protection modes they actually cover, contrasting line to earth, line to neutral and neutral to earth paths so the practical difference becomes clear rather than theoretical, and closes with the questions installers most often ask.

Surge Protection Single Phase vs Three Phase: 5 Differences

Single phase and three phase surge protection are not competing product grades but matched responses to different electrical supplies, and confusing the two leads to devices that cannot protect properly or will not fit the board. This comparison sets out five differences that determine the correct choice. It covers supply voltage and pole configuration, contrasting 1P, 1P+N and 2P single phase devices with 3P, 3P+N and 4P three phase units, and explains the protected modes and earthing arrangements each supports. Further sections compare typical applications and installation locations, sizing and wiring requirements, and the difference in cost and panel space. A summary table presents both options side by side, and a practical section explains how to identify which one an installation actually needs, including sites where both supplies are present.

5 Ways a 50kA Surge Protector Fails and How to Prevent It

A 50kA surge protector that has silently reached end of life offers no protection while still appearing installed and intact. This article examines five ways these devices fail in service and the specification or installation practice that prevents each one. It covers cumulative degradation from repeated surge events, continuous overvoltage stress caused by an undersized Uc rating, thermal runaway when the disconnect cannot respond quickly enough, backup fuse and short-circuit rating errors that leave the device unprotected at end of life, and excessive connection lead length that raises the effective protection level far above the datasheet figure. A dedicated section describes the symptoms that reveal each failure, from status indicator changes and tripped backup devices to thermal signs, followed by a prevention checklist for 50kA installations.

Type 1 Surge Protector vs Type 1+2: Key Differences

At the service entrance, specifiers face a choice between a dedicated Type 1 surge protector and a combined Type 1+2 unit, and the decision affects both protection quality and panel cost. This comparison sets out five differences that determine which is appropriate. It contrasts protection scope, where a Type 1 device handles partial lightning current while a combined unit also addresses switching surges, and explains the test classes behind each, from Iimp on the 10/350 microsecond waveform to the combined ratings of a Type 1+2 product. Further sections compare voltage protection level and what actually reaches downstream equipment, panel space, wiring and coordination requirements, and the total cost of two separate devices against one combined unit, with a summary table and decision scenarios.