Karakteristik produk:
| Spesifikasi | BR-50GR 150 2P | BR-50GR 275 2P | BR-50GR 350 2P | |
| Klasifikasi SPD menurut EN61643-11 | Tipe 1 + Tipe 2 | Tipe 1 + Tipe 2 | Tipe 1 + Tipe 2 | |
| Klasifikasi SPD menurut IEC61643-11 | Kelas I + Kelas II | Kelas I + Kelas II | Kelas I + Kelas II | |
| Tegangan operasi nominal | Tidak | 120V(50/60Hz) | 230V(50/60Hz) | 250V(50/60Hz) |
| Maks. operasi terus menerus a.c. voltase | Uc | 150V(50/60Hz) | 275V(50/60Hz) | 350V(50/60Hz) |
| Arus impuls petir (10/350μs) | Imp | 50kA | 50kA | 50kA |
| Arus pelepasan nominal (8/20μs) | Di dalam | 50kA | 50kA | 50kA |
| Maks. arus pelepasan (8/20μs) | maksimal | 160kA | 160kA | 160kA |
| Jumlah muatan listrik | Q | 25As | 25As | 25As |
| Energi spesifik | W/R | 625kJ/Ω | 625kJ/Ω | 625kJ/Ω |
| Tingkat perlindungan tegangan | Ke atas | ≤1.5kV | ≤1.5kV | ≤1.5kV |
| Peringkat arus hubung singkat a.c. | Isccr | 25kA rms | 25kA rms | 25kA rms |
| Maks. sekering cadangan | 350A gG | 350A gG | 350A gG | |
| Tahan TOV tegangan lebih sementara | UT | 230V/120 menit. | 440V/120 menit. | 580V/120 menit. |
| Waktu respons | ta | ≤100ns | ≤100ns | ≤100ns |
| Kisaran suhu pengoperasian | kamu | -40℃-80℃ | -40℃-80℃ | -40℃-80℃ |
| Status pengoperasian/indikasi kesalahan | hijau/merah | hijau/merah | hijau/merah | |
| Luas penampang (Min.) | 4mm² | 4mm² | 4mm² | |
| Luas penampang (Maks.) | 35mm² | 35mm² | 35mm² | |
| Untuk pemasangan | Rel Din 35mm | |||
| Bahan penutup | Termoplastik UL94-V0 | |||
| Tingkat perlindungan | IP20 | IP20 | IP20 | |
| Kode Pesanan | B17162 | B18127 | B17188 | |
| Kode Pesanan (Dengan sinyal jarak jauh) | B17163 | B18128 | B17189 | |
Fitur:
BR-50GR 2P is suitable for TN system.
Poles number: 2P.
Width of one pole: 36mm.
Uc 150V / 275V /350V can be achieved.
Fault indication via red mark in the inspection window.
35mm DIN rail mountable.
With remote signaling contact for control device for your option.
In accordance with EN / IEC 61643.
High security performance.
Easy maintenance.
Red indicates broken, replacement notice, which is clear and easy distinguished.
Aplikasi:
Used in the main distribution boards, for use primarily on mains power distribution systems to protect connected facility from transient overvoltage.
Suitable for the low voltage main power distribution cabinet/box of buildings, and the facility connected between single phase AC power supply and system in parallel.
Use of attention:
1. The grounding path should be as short as possible, and the length should not exceed 1.5 meters.
2. When installing, pay attention to cables coming in and out of surge protective devices, so as to avoid the two coupling of surge.
3. The protected equipment must have good grounding, and the grounding impedance is in accordance with the relevant national standards.
4. After correct installation, it can work steadily for a long time. If it is found that the transmission performance of the system is reduced or the signal is interrupted due to the cause of surge protection, it should be maintained or replaced in time.
Informasi lebih lanjut atau konsultasi pribadi? Produk dan pengetahuan kami hadir untuk memberikan solusi.
Optimized by Seraphinite Accelerator
